|
|
|
|
|
|
|
|
|
首页 >>> 产品目录 >>> 活细胞工作站 >>> 显微镜用活细胞培养系统
|
|
产品[笼式CO2显微镜培养箱]资料
|
如果您对该产品感兴趣的话,可以 
产品名称:
笼式CO2显微镜培养箱
产品型号:
CO2 Microscope Cage Incubator
产品展商:
自然基因科技有限公司(NatureGene Corp.)
简单介绍
笼式CO2显微镜培养箱设计用于保持在显微镜工作站周围细胞培养所需的环境条件，因此可以进行对生物学样品的长时间观察；同时保证其他设备有足够的空间。在笼式显微镜培养箱中，细胞增殖速度与常规台式培养器中相同。
|
| 笼式CO2显微镜培养箱的详细介绍 |
有各种型号，适用于几乎所有倒置显微镜以及直立式显微镜。有广阔可选范围的腔室和可更换平板适配器，因此仪器非常灵活，可以支持任意细胞培养容器 (培养皿，载波片，多孔板，等) |
| |
| 温度范围 | 高于室温3°C到 50°C | | 温度控制精度 | ±0.1°C | | 加热技术 | 热气流 | | 控制器类型 | 软件 / 需要计算机 | | 温度反馈 | 样本温度反馈 | | 湿度模块 | 加热 | | 二氧化碳范围 | 0 到 100% | |
样本温度调节 在培养皿里直接测量温度，通过一个PID控制器控制温度：经由风扇把热空气吹入显微镜周围的塑料盒子。PID 控制器从参考井中测量温度并且更新风扇加热器的温度，保证样本温度稳定在 ± 0.1°C. |  | CO2 二氧化碳和湿度调节 CO2 二氧化碳在控制器里与空气混合然后注入微环境腔室，以控制基质的酸碱度. 在整个实验过程中都可以记录并控制二氧化碳的浓度水平. 根据需要，第三股气流可以注入培养腔室。一个加热湿度模块可以阻止培养基质的蒸发，并且避免水冷凝在玻璃和塑料表面。. |  | 微环境腔室 微环境腔室用于显微镜载物台并容纳样本。二氧化碳和空气混合气流经过预混和预加热后持续注入腔室。可替换的适配器可以容纳任意种类细胞培养容器。 |  |
技术数据 | 热稳定性 0.1°C | 
| Biaync
ay
o | 与台式培养器相当的细胞增殖情况 | 
|
Bianco
| 每日基质蒸发小于2% | 
|
Features
Several windows on the front and side panels allow full and easy access to the microscope. In particular, two openings on the bottom of the front panel give fast access to the focus knob. Additional windows can be realized upon request. | | |
|
Turn to open hinges allow a one minute removal both of the front and of the upper panel. Once the panels have been removed, the rest of the cage incubator can be easily moved backwards. When needed, the cage incubator can be reassembled and placed again around the microscope in 5 minutes. | | |
|
Inverted and Upright Microscopes
Mixer or Controller?
Okolab Microscope Incubators can be alternatively equipped with two types of CO2 Modules: a Manual CO2 Mixer or a Digital CO2 Controller. Manual CO2 Mixer It allows to generate COB2B-Air mixtures with an adjustable COB2B concentration in the range 0-15%. Air and COB2B flows are regulated by two floating ball flow meters in the range 0.2 1.7 Nl/min and 0.013 0.13 Nl/min, respectively.
|  | Digital CO2 Controller It allows to generate a CO2-Air mixture with an adjustable CO2 concentration in the range 0-20%, with an accuracy of ± 5% of CO2 concentration, for instance, if CO2 set point is 5%, accuracy is ± 0.25% . The air flow is regulated by a floating ball air flow meter in the range 0.2 0.8 Nl/min. Sensing Technology A CO2 infrared sensor continuously measures CO2 concentration in the mixed gas stream and a PID closed loop controller gives feedback to a fine valve regulating CO2 flow. Measured value of CO2 concentration is displayed in real time in green . An alarm can be set on CO2 concentration, so that, if CO2 concentration goes below such value, display color turns red and a buzzer turns on. Data Storage The serial RS-232 interface and the CO2 Control Software allow the user to control the unit with a personal computer and to acquire and store concentration data in computer memory. |  |
Digital CO2 Controller's Technical Data CO2 Concentration Profile 
CO2 cycles 
Available chambers for MCI
The CO2 Microscope Cage Incubator line is very flexible, thanks to the broad variety of micro-environmental chambers and interchangeable plate adapters available. The aim of the Micro-Environmental chamber is to create a closed environment around the specimen where feeding humid air and CO2.
The choice of the most suitable chamber depends on the type of XY stage (flat mechanical stages, ASI stages and Piezoelectric stages require a different chamber from the other stages).
Each chamber can accommodate any kind of multiwell plate and can be equipped with plate adapters, chosen according to the type of cell culture support used (Petri Dish, glass slide, etc. ). A one screw mechanism allows to change the plate adapters in 30 seconds, so that the same chamber can be used with different cell culture supports.
Every chamber presents holes to allow perfusion tubes' insertion. The Lowered lid allows the high N.A. condensers use.
List of available chambers: |
| Universal for Manual Stage: Especially designed to fit on mechanical flat XY stages. It accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top | 
| | 
| | | | | Universal for Motorized Stage: This model is designed to fit any 160x110mm sized stage (i.e. Ludl BioPrecison and BioPoint, Marzhauser SCAN IM 120x100, Prior H107 and H117), A.S.I. stages and all mechanical flat stages. A dedicated stage insert to fit it into the Nikon TI-S-E motorised XY stage is also available. This chamber model accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top | 
| |
| | Universal for ASI - Stage: Especially designed to fit into ASI XY stages. It accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top |
| |
| | Chamber for Piezoelectric Stage: Special design for Prior NanoScan PZ100 Z Piezo Stage. It allows to use #1 35mm Petri-dish or #1 glass or chamber slide. Back to top | 
| | Lowered lid: Thank to its lowered profile, this special design lid allows to work with high N.A. condensers. It can be mounted on the Universal MEC for Manual Stages and on the Universal MEC for motorized stages, by replacing their standard lid. Back to top | 
| |
Accessories
Obscuring panels can be assembled with the cage incubator by means of turn to open hinges. They will create a dark environment for your fluorescence experiments. | | |
|
Upon request, a third gas can be fed into the incubating chamber. Different percentages of three gas (typically CO2, O2 and air) are mixed in the control unit and are continuously fed into the incubating chamber to control medium pH and other experimental parameters. | | |
|
Read Temperature Software is available to read incubator temperature and store the data in computer memory. | | |
Back to top |
FOCUS ON THE CO2 MICROSCOPE CAGE INCUBATOR The space around my microscope is quite limited. Let me define my microscope set-up as non-standard. Can your cage incubator fit my system? Yes, it can. In this case, one of our application scientists will come to your lab to customize cage drawings. I would like to feed a third gas stream (i.e. Oxygen) besides CO2 and air in the microscope incubator. Is this possible? Yes, it is. Please, specify this special request when placing your order. I was looking for a cage incubator for upright microscopes. Is it available? Yes, it is. The Microscope Cage Incubator is the solution we offer for upright microscopes.
|
|
|
|
|